(1) or the disk must be assigned to the center, crushing cavity is not possible, directly into the mineral. Because it is easy to overload switch is illegal to wear a liner.
The law provided Hours:
a distribution plate of ore distributes evenly in the crushing chamber.
b can not pull the minerals to be greater than the height of the mortar
(2) the largest ore crusher to the size of eligible population size is equal to me, (the maximum size ofore block ≤ 85% of the mining population size) or will lead to:
a mill decreased.
b crusher damage some of the other pieces.
(3) No load start-breaker, the load is the beginning of the accident.
(4) parking, you must first stop the mining machine, and so the ore was crushed in the crushing chamber after release, the car crusher.
work (5) crushers should always check to identify the pressure and the hydraulic locking, computer,Problems and early treatment.
2. Crusher output
output methods of the cone crusher and nutrition, feeding the fragmentation, the degree of relief block size, the physical and mechanical properties of the mineral, temperature and other relevant, varied, was released to the conditions of the general rate to be specified .
3. Rolling replacement mortar
Malta rolled into a U-shaped screw on the collar, between the injection of zinc alloy, the nearestintegrated with the new installation or replacement of the acetabular wall material in 6-8 hours, check the attachment, U-shaped and tighten the screws.
4. Cone Crusher replacement wall
cone crusher with a cone head wall is replaced with the cone on the body between the two casting zinc alloy, or a new installation of a new cone crusher wall work 6-8 hours, check the connection is fixed , attachment should be dissolved immediately found.
5. Meshing
Since the circularfriction wear plate, the change of the gap, you have to ensure the meshing gears are covered with pads on the bottom more, must bear the seal of the thickness of the circular plate.
6. Bearings and Seals Bowl
Install the drum support, not to damage the locking ring rope (use of hardwood and other objects between the wire support).
Assembly spherical bearing cockroaches crushing cone and the plate to ensure that eachBall in contact with the inside cylindrical 0,35-0.5 mm should ensure that the ring gap.
perfusion Bowl around the bush is made of alloy bar obsession for the bowl on the shelf around the bowl to prevent any bearing on the circumference of rotation.
Bowl support frame and the body frame with the key (PIN) is fixed, and if the bowl support frame and the body frame can be found with the game must be treated immediately.
7. Cylindrical shell and the framework for third placefit of transition, to prevent rotation of the bush, but also in the top outlet in the tank in zinc alloy, replace the bushings when should the actual size of the body frame to be prepared for after a long day of work and the use Hammer inevitable consequence of working with change. If the gap is too general a coating lead to breakage.
8. Conical bush
eccentric shaft sleeve together and in the air to avoid the injection of spin case study zinc alloy to be filled with allinterstitial zinc alloy, zinc alloy injection issue due to the thermal deformation of the sleeve, so check the size of the cone new set of D1, D2, and B, must be prompt correction is not correct, the production spare parts, but keep the actual size of the internal diameter of the eccentric original preparation.
9. Spring
(1) the role of the spring, when the mill is not broken in the mill, in order to protect the property is not damaged, so that theSpring and pressure force mill suitable when the switch is in normal operation of the spring does not move, just lay in the crushing chamber overload when iron lift switches compressed spring sleeve is the phenomenon occurred.
(2) cones, when the top of the normal beat, this is not a normal phenomenon must be carefully analyzed the causes and take steps to eliminate, if not the lack of compressed spring is working not only normal, but part of thethe damage that can occur because of the compression spring causes the increase of tensile strength.
Breakers beat the highest score for several reasons:
Irregular or mine mine
B to the mine in small pieces and powder, minerals and excess moisture.
C port of discharge gap is too small.
10. Open the rotating parts must have a cover, but includes a shield for the user.
Friends Link : Spirits USA Hidef camcorder reviews Inflatable bounce houses Omron Pedometer reviews
